How to Get Repaired Kitchen Plumbing Problems?


Most of kitchen plumbing problems are minor. Certain most common issues occur in the kitchen include a loose pipe, a leaking tap and an overloaded drain trap. Since these are minor problems, calling a plumber can be costly and time consuming. If you know how to repair these minor kitchen plumbing issues, then you can avoid plumber expenses.

Determine the problem

First check and find out where the problem is. Drippage in two-control tap might be having issue inside the faucet housing, and may its washer have worn down. Washers are used to avoid drippage by keeping the metal closeoff valve inside the tap sealed. If it is a leakage under the sink, then switch the water on and look for a loose pipe.

Sometimes, the drain faucet beneath the sink may cause problems when clogs form there. Drain trap is a U-shaped tube extending from the sink to the wall.

Kitchen Plumbing How to Get Repaired Kitchen Plumbing Problems?

Stop the tap water supply

When you have determined the real problem, switch off the tap water supply. You can see the two closeoff valves either at the ground or near the sink that controls the water flow to the tap. Two closeoff valves are used for hot and cold water supply respectively. Switch on the tap using handles to drain out any remaining water. Now, you can work on the tap. It is recommended to change washers and make the pipes tighter at the same time.

Change the faucet controls

Use a crescent wrench to move out one of the tap valve stem. The stem will look a little similar of a spark plug and includes a washer. Washer is fixed at the bottom of the stem and you need to unscrew the washer. It is available in different sizes and so, purchasing one or two of the correct size will be easier if you take it to the hardware shop.

Tighten the new washer to the bottom of the stem. Enclose a small piece of thread seal tape on the threads of the stem and tight the stem back to the valve. Turn on the control and repeat the procedure for the remaining one.

Fasten the nuts

Employ a wrench to fasten the nuts that control the hot and cold water supply line to the beneath of the tap that access them under the sink. Generally supply lines are made of flexible tubing with a threaded nut on both ends. Once you have fastened the nuts, discharge water and look for leaks. If you find any leak, then use thread seal tape to the threads. Even after the leak continues, bring the flexible tubing to hardware shop and buy a replacement.

Loosen the big nuts

Loose the big nuts that control the drain trap in place. It is a U-shaped pipe at the bottom of the sink and is the main area for clogs. Pull the pipe off in a smooth manner and clean it out. Change the drain trap pipe and put some thread seal tape to the threads. Also examine the remaining drainage pipes to ensure that they are firmly held in place. Switch on the water, and your project is completed!!




Via: How to Get Repaired Kitchen Plumbing Problems?

Pembaca yang baik pasti SELALU meninggalkan Komentar

{ 9 komentar... read them below or add one }

Unknown mengatakan...

I read your blog and found the information about the How to Get Repaired Kitchen Plumbing Problems..........
Thanks for sharing
Hot water repair


Unknown mengatakan...

A dripping tap is one of the most common kitchen plumbing issues that can be repaired easily. Washers are most often the reasons why the tap drips. When replacing the washers, make sure you properly reassemble the three kinds of washers, which are the o-ring, the body washer, and the jumper valve. These have different sizes, so make sure that you have the right replacement for each type of washer.


-Carmella Vancil

Darryl Iorio mengatakan...

This is really helpful for those who want to fix their kitchen sink alone. Though I think it can be used on any faucet. I even do the same thing on my bathroom sinks. You can really save a lot of money when you can do it yourself, but if you can afford it, have a plumber check -- just in case it is different from what you thought.

Darryl Iorio

Unknown mengatakan...

You can’t solve or mend anything, not unless you know what the problem is. Also, make sure that you know how your way around the plumbing, or better yet, just have it serviced by a plumber. You’ll save a lot of money if you do the repairs on your own, but if you don’t know anything, then fixing it yourself might do more harm.

-Althea Tumlin

Unknown mengatakan...

The most important aspect to consider when planning a kitchen is the location of all your plumbed items. This is best done in conjunction with a plumber, who will be able to advise you on all the practicalities of placement. This is especially important when you are remodelling or renovating, as your new configuration may not be able to be accommodated by the existing plumbing fixtures. Items like dishwashers should ideally be placed as close as possible to the water inlets.

sydney plumber

Unknown mengatakan...

Your kitchen sink is a plumbing hub within your home. You use it for loads of different things, and if it is not working as it should, you are heavily impacted, and your mood is impacted negatively as well.

toilet plumber  service

Harris mengatakan...

I went through your blog and found it informational as how to deal with Plumbing problems.
Thanks for sharing!

Ezra mengatakan...

Its always good toi have a basic information about general Plumbing solutions.
Thanks for sharing...

Kathryn mengatakan...

That's a very helpful blog.
We frequently come across Kitchen Plumbing problems.
Thanks for sharing.

Posting Komentar